***************************************************************************** 
                                  MultLang.TXT
***************************************************************************** 
This file presents general information about the Symbios Multilanguage
Configuration Utility, Version 4.12.00.

This text file is divided into the following sections:

Multilanguage Configuration Utility
   Starting the Multilanguage Configuration Utility
   Main Menu
      Change Adapter Status
      Adapter Boot Order
      Additional Adapter Configuration
   Utilities Menu
      Adapter Setup Menu
      Device Selections Menu
   Quitting the Multilanguage Configuration Utility


*  *  *  *  * Starting the Multilanguage Configuration Utility *  *  *  *  *  *

If you have SCSI BIOS version 4.XX, and it includes the Symbios SCSI BIOS 
Configuration Utility, you can change the default configuration of your SCSI 
host adapters. You may decide to alter these default values if there is a 
conflict between device settings or if you need to optimize system performance. 
The Multilanguage Configuration Utility is a stand alone configuration utility, 
which is not invoked at boot time.

To initialize this utility, type:

  PCI_CNFG.EXE

at the DOS command prompt:

This executable program will launch the multilanguage menu driven utility. 

To make changes with this utility, one or more Symbios SCSI host 
adapters must have NVRAM (non-volatile random access memory) to store the
changes. 


IMPORTANT: The Multilanguage Configuration Utility is a powerful tool. If, while
           using it, you somehow disable all of your controllers, pressing Ctrl-A
           (or Ctrl-E on version 4.04 or later) after memory initialization
           during reboot allows you to re-enable and reconfigure.

Note: Not all devices detected by the Configuration Utility can be controlled 
      by the BIOS. Devices such as tape drives and scanners require that a
      device driver specific to that peripheral be loaded.

*  *  *  *  *  *  *  *  *  *  * Main Menu *  *  *  *  *  *  *  *  *  *  *  *

When you start the Symbios Multilanguage Configuration Utility, the Main Menu 
appears. This menu displays a list of up to four Symbios PCI to SCSI host
adapters in your system and information about each of them.

To select an adapter, use only the arrow keys and enter key. Then you can view
and/or change the current settings for that adapter, and the SCSI devices
attached to it. 

Select an adapter only if Current Status is "On". Changes are possible
only if NVRAM on your adapter is present. Selections that are not permissible
will be grayed out.      

Here is an example of the Main Menu:
    
    Main Menu

                 Port      Irq  --------Status--------- NvRAM
                 Num      Level Current      Next-Boot  Found
    SYM53C895    FC00       9      On            On       Yes
    SYM53C896    F800       9      On            Off      Yes
    SYM53C896    F400       9      On            Off      Yes
    Change Adapter Status
    Adapter Boot Order
    Additional Adapter Configuration 
    Display Mode = Verbose 
    Mono/Color
    Language
    Help 
    Quit

Below the list of host adapters on the Main Menu display, you see eight
options. They are described in detail below. If these settings are altered,
the system reboots upon exit from the Configuration Utility via the Quit
option.


*   *   * Change Adapter Status *   *   *

The change adapter status allows you to activate or deactivate a host adapter 
and all SCSI devices attached to it. When this option is used to make 
a change, the change takes place after the reboot upon exit from the utility. 
Here is an example of the Change Status on Next Boot menu: 

    Main Menu

    Change Status on Next Boot:
               Port    Irq  ---------Status-------- NvRAM
               Num    Level Current      Next-Boot  Found
    SYM53C895  FC00     9      On           On        Yes
    SYM53C896  F800     9      On           Off       Yes
    SYM53C896  F400     9      On           Off       Yes

To change an adapter's status, select it and press Enter. Then press the
Escape (Esc) key to exit from this menu.


*   *   * Adapter Boot Order *   *   *

The adapter boot order allows you to set the order in which host adapters 
will boot when you have more than one Symbios host adapter in your 
system. When this option is selected, the Boot Order menu appears. Here is
an example of the Boot Order Menu: 

    Main Menu 

     BootSeq            Bus   DevFunc  BootSeq           Bus  DevFunc
       0     SYM53C896   00     A0         1   SYM53C896  00     98
       2     SYM53C895   00     90


To change an adapter's boot order, select it and press Enter. You are then 
prompted to enter the new boot sequence number. To remove an adapter's boot 
order, press Enter again rather than entering a new sequence number. While 
the maximum capacity is 32 adapters, only 0 through 3 can be assigned a
boot order. If an invalid number is entered, an error message appears. When 
the adapters are ordered as desired, press the Escape (Esc) key to exit from
this menu and reboot.        


*   *   * Additional Adapter Configuration *   *   *

The additional adapter configuration allows you to configure an adapter that 
is not assigned a boot order. When this option is selected, the Adapter 
Configuration menu appears. Here is an example of the Adapter Configuration 
Menu:

     Main Menu

       BootSeq            Bus   DevFunc  BootSeq           Bus  DevFunc 
          1    SYM53C896   00      A0       0    SYM53C896  00     98   
               SYM53C895

Highlight the adapter to be configured and press Enter. The message "Resetting
Adapter, Please wait" appears, and then the system scans for devices. Finally,
the Utilities Menu appears and lists the available options, which are described
below.


*   *   * Display Mode *   *   *

The Display Mode option determines how much information about your host adapters 
and SCSI devices appear on your computer monitor during boot. For more 
complete information, choose the verbose setting. For a faster boot, choose 
the terse setting.


*   *   * Mono/Color *   *   * 

The Mono/Color option allows a choice between a monochrome or color display for
the SCSI BIOS Configuration Utility. You might need to choose the mono setting
to get a more readable screen on a monochrome monitor.


*   *   * Language *   *   * 

If enabled, the Language option allows the user to select from ten languages for
the Configuration Utility: English, German, French, Italian, Spanish, Polish,
Swedish, Portugeuse, Czeck, and Danish.  


*   *   * Help *   *   * 

The Help option allows the user to bring up a help screen with information 
about the Main Menu.


*   *   * Quit *   *   * 

The Quit option allows exiting from the SCSI BIOS Configuration Utility when 
the Main Menu is displayed.


*   *   * Esc *   *   * 

The Esc option allows exiting from all the screens except the Main Menu.  


*  *  *  *  *  *  *  *  *  *  * Utilities Menu *  *  *  *  *  *  *  *  *

When you select a host adapter on the Main menu, the Utilities menu appears:

    SYM53C895
      Utilities

                 Adapter Setup
                 Device Selections
                 Help
                 Exit this menu

Choose Adapter Setup to view and change the selected adapter settings. Choose
Device Selections to view and change settings for the devices attached to the
selected adapter.

You are returned to this menu after making changes to the configuration of 
any host adapter or connected SCSI device. Before you exit this menu, you are
prompted to save or cancel any changes.


*  *  *  *  *  *  *  *  *  *  * Adapter Setup Menu *  *  *  *  *  *  *  *  

When you select Adapter Setup, the corresponding menu appears. Here is an
example of the Adapter Setup menu: 

     
       Adapter Setup

         SCAM Support               Off
         Parity                     Enabled
         Host SCSI ID               7
         Scan Order                 Low to High <0..Max>
         Removable Media Support    None             
         CHS Mapping                SCSI Plug & Play Mapping
         Spinup Delay (secs)        2
         Secondary Cluster Server   No
         Termination                Auto
         Help
         Restore Default Setup
         Exit this menu

The settings in this menu are global settings that affect the selected host 
adapter and all SCSI devices attached to it. One of these choices can be 
selected by highlighting it and pressing Enter. 


*   *   * SCAM Support *   *   *

The Symbios BIOS version 4.XX supports the SCSI Plug and Play protocol called
SCAM (SCSI Configured AutoMatically). SCAM support by default is off in 
versions 4.09 and later. The user may choose to turn this on. Note that if this 
BIOS is flashed onto a board with existing settings, then these settings will 
not be changed to reflect the new BIOS defaults. 


*   *   * Parity *   *   *

The Symbios PCI to SCSI host adapters always generate parity, but some older 
SCSI devices do not. Therefore, you are offered the option of disabling 
parity checking.

Note:  When disabling parity checking, it is also necessary to disable 
       disconnects for all devices, as parity checking for the reselection 
       phase is not disabled. If a device does not generate parity, and it 
       disconnects, the I/O never completes because the reselection never 
       completes.


*   *   * Host SCSI ID *   *   *

This option refers to the host adapter's SCSI ID, which is a unique number used
to identify the device on the SCSI bus.

Note: In general, it is suggested that you do not change your host adapter ID 
      from the default value of 7, as this gives it the highest priority on the
      SCSI bus. Please also note that if you have 8-bit SCSI devices, they
      cannot see host IDs greater than 7.


*   *   * Scan Order *   *   *

This option allows the user to tell the SCSI BIOS and your device drivers to 
scan the SCSI bus from low to high (0 to max) SCSI ID, or from high to low (max 
to 0) SCSI ID. If there is more than one device on the SCSI bus, changing 
the scan order changes the order in which drive letters are assigned by the 
system.

Note: This Scan Order option may conflict with operating systems that
      automatically assign a drive order.


*   *   * Removable Media Support *   *   *

This option defines the removable media support for a specific drive. 
When this option is selected, a window appears with three choices: 

     o  None
     o  Boot Drive Only 
     o  With Media Installed

     None indicates there is no removable media support whether the drive 
     is selected in BBS as being first, or first in scan order in non-BBS.

     Boot Drive Only provides removable media support for a removable hard
     drive if it is first in the scan order.

     With Media Installed provides removable media support wherever the drive(s) 
     actually resides. 

One of these choices can be selected by highlighting it and pressing Enter.


*   *    * CHS Mapping *   *   *

This option defines the cylinder head sector (CHS) values that will be mapped 
onto a disk without pre-existing partition information. SCSI Plug and Play 
Mapping is the default value.

To support interchange with non-compatible systems, there is another option 
that can be selected by choosing CHS Mapping and then cursoring to "Alternate 
CHS Mapping". 

Note: Neither of these options will have any affect after the disk has been
      partitioned with the FDISK command.

To remove partitioning, two options are available:

     o  Reformat the disk using the Format Device option. See the section "Device
        Selections Menu" below.
        
     o  Use the FDISK /MBR command at the C:\ prompt, where MBR represents master 
        boot record.  

Important: Reformatting the disk or using FDISK /MBR erases all partitioning and 
           data that exists. Be careful when using either the Format utility or
           the FDISK /MBR command that you target the correct disk.

Note: After clearing the partition data, it is necessary to reboot to clear
      memory or the old partitioning data will be reused, thus nullifying the
      previous operation.


*   *    * Spinup Delay (secs) *   *   *

This option allows the user to stagger spin ups between devices for a longer
period of time to balance the total current load. The default value is 2 seconds
with choices between 1 and 10 seconds.
 
This is a power management device designed to accommodate disk devices that may
have heavy current load during power up. If multiple drives are being powered
up simultaneously and drawing heavy current loads, then this option staggers the
spin ups to limit startup current.


*   *   * Secondary Cluster Server *   *   *

This option allows the user to enable an adapter to join a cluster of adapters
without doing any SCSI bus resets. This is a requirement for Microsoft Cluster
Server. The default value is No with an alternate value of Yes.


*   *   * Termination *   *   *

This option allows the user to have termination control providing an adapter has
controllable termination. The default value is Auto termination. The alternate
value is Off.


*  *  *  *  *  *  *  *  *  * Device Selections Menu *  *  *  *  *  *  *  *  *

When you select the Device Selections option, the corresponding menu appears:

     SYM53C895
     Device Selections 0-7

                      Sync   Data   Disc   Time      Scan      Queue  Initial
                      Rate   Width          Out   Bus   LUNS   Tags     Boot

     Seagate 31051N   20      8      On     10    Yes    Yes    On       No
     1-Dev1 N/A       80      8      On     10    Yes    Yes    On       No
     2-Dev2 N/A       80      8      On     10    Yes    Yes    On       No
     Quantum Lighting 20      8      On     10    Yes    Yes    On       No
     4-Dev4 N/A       80      8      On     10    Yes    Yes    On       No
     IOMega ZIP 100   20      8      On     10    Yes    Yes    On       No
     6-Dev6 N/A       80      8      On     10    Yes    Yes    On       No
     SYM53C895
     Device Selections 8-15
     Help
     Exit this menu

The settings in this menu affect individual SCSI devices attached to the 
selected host adapter. Changes made from this menu do not cause the system 
to reboot upon exit from the SCSI BIOS Configuration Utility. To change a value, 
select the required device by using the arrow keys and press Enter. A new menu
appears providing the options and utilities available. For example, you could
cursor to Sync Rate to change the Sync Rate value of the chosen device.  


*   *   * Device Name *   *   *

     Inside device
          Sync Rate
          Width
          Disconnect
          Read/Write I/O Timeout (secs)
          Scan for Device at Boot Time
          Scan for SCSI LUNs
          Queue Tags
          Initial Boot
          Format
          Verify
          Help
          Restore Default Setup             
          Exit this menu

Please review the descriptions of each option below before changing any values.

*   *   * Sync Rate (mega Bytes/sec) *   *   *

This option defines the maximum data transfer rate the host adapter will attempt
to negotiate. The host adapter and a SCSI device must agree to a rate they can
both handle.


*   *   * Width (bits) *   *   *

This option defines the maximum SCSI data width the host adapter will attempt to
negotiate. The host adapter and a SCSI device must agree to a width they can both
handle. Only host adapters that can do 16-bit data transfers have this option 
enabled. 


*   *   * Disconnect *   *   *

SCSI devices have the ability to disconnect from the initiator during an I/O
transfer, thus freeing the SCSI Bus to allow other I/O processes.
This option tells the host adapter whether or not to allow a device to 
disconnect. Some devices run faster with disconnects enabled (mostly newer
devices), while some run faster with disconnects disabled (mostly older 
devices).


*   *   * Read Write I/O Timeout (secs) *   *   *

This option sets the amount of time the host adapter waits for a read, write,
or seek command to complete before trying the I/O transfer again. Since this
provides a safeguard allowing the system to recover if an I/O operation fails, 
it is recommended that you always set the time-out to a value greater than zero.
A zero value allows unlimited time for an operation to complete and could result
in a system hang-up if the operation could not complete.


*   *   * Scan for Device at Boot Time *   *   *

Set this option to "No" if there is a device that you do not want to be available 
to the system. Also, on a bus with only a few devices attached, the user can 
speed up boot time by changing this setting to "No" for all unused SCSI IDs. 


*   *   * Scan for SCSI Logical Units (LUNs) *   *   * 

Set this option to "No" if you have problems with a device that responds to all
LUNs whether they are occupied or not. Also, if a SCSI device with
multiple LUNs exists on your system but you do not want all of those LUNs to be
available to the system, then set this option to "No." This will limit the scan
to LUN 0 only.


*   *   * Queue Tags *   *   *

This option enables or disables the issuing of queue tags during I/O requests
when your device driver can do this.


*   *   * Initial Boot *   *   *

This option allows any device attached to the first adapter to become the
boot device. It provides the users of non-BBS personal computers some of the
flexibility of a BBS machine.


*   *   * Format *   *   * 

If enabled, this option allows low-level formatting on a disk drive.
Low-level formatting will completely and irreversibly erase all data on the
drive.

Note: Formatting will default the drive to a 512 byte sector size even if
      the drive had previously been formatted to another sector size.


*   *   * Verify *   *   * 

This option reads all the sectors on a disk to check for any errors. When
selected, this option displays the following message: 

      "Verify all sectors on the device
       Press ESC to abort
       Else press any key to continue"


*   *   * Help *   *   * 

This option provides a help screen with information about the current menu.


*   *   * Restore Default Setup *   *   * 

This option resets all device selections back to their optimal settings. Select 
this option to restore all manufacturing defaults for the specified adapter. 
Note that all user customized options will be lost upon saving after restoring 
default setup. 


*   *   * Exit this menu *   *   *

This option leaves the current menu screen and returns to the previous screen.


*  *  *  *  *  *  To Exit the Multilanguage Configuration Utility *  *  *  *  *

Since some changes only take effect after your system reboots, it is 
important that you exit this configuration utility properly. Return to the
Main menu and exit via the Quit option. If you reboot the system without
properly exiting from this utility, some changes may not take effect.
  