---------------------------------------------------------------------- S3 Video Device Driver for Windows NT 4.0 Driver Version 1.03.11 README File ---------------------------------------------------------------------- This file contains procedures for installing from diskette the S3 Trio video device driver for Windows NT 4.0; it also contains other video- related procedures. The following topics are included in the file: 1.0 Supported Color Depths and Refresh Rates 2.0 Installing the S3 Video Device Driver for Windows NT 4.0 3.0 Configuring Your Monitor 4.0 Changing the Video Settings 5.0 Setting Your Monitor to VGA Mode 6.0 Trademarks 1.0 Supported Color Depths and Refresh Rates _____________________________________________ +================+=========================+====================+ Resolution Color Depths Refresh Rates (Pels) (Hz) +----------------+-------------------------+--------------------+ 640 x 480 256, 65536, 60, 72, 75, 85 16777216 +----------------+-------------------------+--------------------+ 800 x 600 256, 65536, 60, 72, 75, 85 16777216 +----------------+-------------------------+--------------------+ 1024 x 768 256, 65536 43 interlaced, 60, 70, 75, 85 +----------------+-------------------------+--------------------+ 1280 x 1024 256 43 interlaced, 60, 75, 85 +----------------+-------------------------+--------------------+ 1600 x 1200 256 48 interlaced, 60 +================+=========================+====================+ Note: Refresh rates listed are supported by the display controller. Your monitor might not support all refresh rates and display modes listed. 2.0 Installing the S3 Video Device Driver for Windows NT 4.0 ______________________________________________________________ Note: If your computer has IBM-preinstalled software, the video device driver for Windows NT 4.0 has already been installed on the hard disk of your computer. However, the information included in this file will be helpful if you ever need to reinstall or update the device driver, or if you want to change the video settings. To install the S3 video device driver: 1. Start Windows NT 4.0 in VGA mode: When the "Please select the operating system to start..." message is displayed, select WINDOWS NT WORKSTATION VERSION 4.00 [VGA MODE]. 2. Click on the START button, select SETTINGS, and then click on CONTROL PANEL. 3. Double-click on the DISPLAY icon. The Display Properties window appears. Note: You can also display the Display Properties window by clicking the right mouse button anywhere on the Desktop and then selecting the PROPERTIES option from the pop-up menu. 4. Click on the SETTINGS tab. 5. Click on the DISPLAY TYPE button. The Display Type window appears. 6. Under Adapter Type, click on the CHANGE button. 7. In the Change Display window, click on the HAVE DISK button. 8. Insert the diskette containing the S3 Trio video device driver for Windows NT 4.0 into drive A; then click on the OK button. 9. From the list of displayed S3 devices, select your S3 Trio device; then click on the OK button. 10. In the Third-party Drivers window, click on the YES button to proceed. o If a message appears stating the driver is already installed on the system, and asks if you want to use the current or new drivers, be sure to select the NEW button. o If prompted for the driver diskette a second time, click on the CONTINUE button. 11. When the message "The drivers were successfully installed" is displayed, remove the driver diskette from the drive; then click on the OK button. 12. In the Display Type window, click on the CLOSE button. 13. In the Display Properties window, click on the CLOSE button. 14. When the System Settings Change window appears with a message asking if you want to restart your computer, click on YES. Note: If you are installing Windows NT 4.00 and the S3 chip set is currently installed in your computer, proceed through the Windows NT installation as normal. The installation program will prompt you to choose a display mode. Click on the CANCEL button from the Display Settings window to ignore this step for now. The installation will now finish. Once Windows NT has started for the first time, proceed to follow the steps outlined above to install the device driver for your S3 device. 3.0 Configuring Your Monitor _____________________________ o To configure a Non-DDC monitor: 1. Start Windows NT 4.0. 2. Click the right mouse button on the Desktop; then select PROPERTIES from the pop-up menu. 3. In the Display Properties window, click on the SETTINGS tab; then click on the DISPLAY TYPE button. 4. In the Display Type window, click on the CHANGE button. The Change Display window appears. 5. Under Manufacturers, click on S3; then under Display, click on the applicable S3 device. 6. Click on the OK button and follow the instructions on the screen. 7. Close the windows you opened; then restart Windows NT if prompted. o To configure a DDC monitor: 1. Start Windows NT 4.0. 2. Click the right mouse button on the Desktop; then select PROPERTIES from the pop-up menu. 3. In the Display Properties window, click on the SETTINGS tab. 4. Under Refresh Frequency, select the HARDWARE DEFAULT setting. 5. Click on TEST to test the new setting; then click on OK. A test pattern is displayed. 6. Click on YES to accept the new setting; then click on OK to end the procedure. 4.0 Changing the Video Settings ________________________________ To change the video settings: 1. Start Windows NT. 2. Click on the START button, select SETTINGS, and then click on CONTROL PANEL. 3. Double-click on the DISPLAY icon. The Display Properties window appears. 4. In the Display Properties window, click on the SETTINGS tab. 5. Make the desired changes; then click on TEST, OK, and then YES. 6. When the changes are satisfactory, click on APPLY and then YES to resize the display dynamically. The Windows NT 4.0 S3 V2 driver includes a utility program called Color Control. This utility allows the user to manipulate the hue, saturation, brightness, and contrast for YUV video overlays. YUV video overlays are often used when playing video files such as MPEG. 5.0 Setting Your Monitor to VGA Mode _____________________________________ To set your monitor to VGA mode: 1. Start Windows NT. 2. Click on the START button, select SETTINGS, and then click on CONTROL PANEL. 3. Double-click on the DISPLAY icon. The Display Properties window appears. 4. In the Display Properties window, click on the SETTINGS tab. 5. Click on the DISPLAY TYPE button. The Display Type window appears. 6. Under Adapter Type, click on the CHANGE button. 7. Under Manufacturers, click on STANDARD DISPLAY TYPES; under Display, click on VGA COMPATIBLE DISPLAY ADAPTER; then click on OK. 8. Insert the appropriate Windows diskettes or CD-ROM, if requested. 9. Click on OK, CLOSE, CLOSE, and then YES to restart your computer. 6.0 Trademarks _______________ The following terms are trademarks of the IBM Corporation in the United States or other countries or both: IBM The following terms are trademarks of other companies: S3 S3 Incorporated Microsoft and Windows NT are trademarks or registered trademarks of Microsoft Corporation. Other company, product, and service names may be trademarks or service marks of others.