IBMSAN.CDM Multi-Path Failover driver for IBM Fibre Channel RAID Controllers Models 1742,3526,3552,and 3542. Refer to the IBM Support Website for the latest information and updated readme file (Refer to section 6.1 below). Last Update: 02/15/02 TABLE OF CONTENTS ================= 1.0 Overview 1.1 Known Issues / Limitations 1.2 Change History 2.0 How to install the driver 3.0 What works 4.0 Unsupported Configurations 5.0 WEB Sites and Support Phone Number 6.0 Trademarks and Notices 7.0 Disclaimer 1.0 OVERVIEW ============ This README file contains the latest information about installing the IBMSAN.CDM Mulit-Path Failover Driver v1.01. This driver must be used with Netware v5.1 or higher and can be used with Novell Cluster Services (NCS) v1.01 or higher. 1.1 Known Issues / Limitations ============================== 1. When running an Novell NetWare NCS Cluster and a path failure affects the Heartbeat volume you may see the volume moving from the preferred path to the alternate path every few seconds in the SM7client. This is corrected by locating the server that is forcing the heartbeat volume to change paths and verify that any path failures are repaired. If a cluster node was brought online during a path failure the IBM FAStT Host adapter driver may need to be unloaded and reloaded after the volume is returned to the preferred path. 2. If IBMSAN.CDM is unloaded prior to deactivating NSS volumes, I/O integrity errors will be displayed and the volume deactivated. The system must be rebooted for the volumes to be reactivated. To fix this problem, before unloading IBMSAN.CDM, first go to the console and is the following command: NSS /deactivate=all 3. You cannot run 'LIST DEVICES','SCAN FOR NEW DEVICES'or 'SCAN ALL" commands while any of the paths are in a failed state. All paths must be restored before these commands can be issued or the LUNs will be deactivated. 4. If a partially managed device is reported when you open Storage Manager verify that the /PORTNAMES switch is being loaded with the HAM driver load. In certain configurations only 1 UTM LUN may be reported since the FAStT Storage Subsystem controllers use the same WWN and different portnames this will allow proper reporting of the disks. 1.2 Change History ================== 1. IBMSAN.CDM version 1.00d to 1.01 Added the IBM 1742 to the scanned devices. - This will allow the UTM LUN to be identified for in-band management of the IBM FAStT700. 2.0 HOW TO INSTALL THE DRIVER ============================= 1. To load the driver, copy the IBMSAN.CDM file to the C:\NWSERVER directory on the server. 2. Edit the C:\NWSERVER\STARTUP.NCF file and make the following changes: a) add the following line after the LOAD SCSIHD.CDM file: LOAD IBMSAN.CDM b) Add the /LUNS (if not already there) and the /ALLPATHS parameters to the QL2200.HAM driver for the FAStT PCI Fibre Channel Adapter. Without these parameters,the alternate paths will be hidden. c) Add the /PORTNAMES parameter to the HAM driver load line. This will allow the proper utilization of the UTM Luns for in-band management. d) Add the /xretry=400 parameter to the HAM driver load line. This will extend the retry count for any I/O command the experiences failure with one of the following SK/ASC/ASCQ codes: 2/04/01 6/8B/02 An example C:\NWSERVER\STARTUP.NCF file is as follows: LOAD MPS14.PSM LOAD IDECD.CDM LOAD SCSIHD.CDM LOAD IBMSAN.CDM LOAD IDEATA.HAM PORT=1F0 INT=E LOAD IPSRAID.HAM SLOT=5 LOAD AIC78U2.HAM SLOT=10005 LOAD AIC78U2.HAM SLOT=10006 LOAD QL2300.HAM SLOT=2 /LUNS /ALLPATHS /PORTNAMES /XRETRY=400 LOAD QL2300.HAM SLOT=1 /LUNS /ALLPATHS /PORTNAMES /XRETRY=400 3. Restart the server for the changes to be made active. 3.0 DRIVER FUNCTIONS ==================== 1. Failover between adapters and controllers on as many paths as can be detected. 2. When a failed path is restored, I/O will fail back to the original path. 3. You can create volumes (both native NetWare and NSS partitions) on the shared storage media. 4. You can type LIST DEVICES at the console and see all the device paths, including the inactive paths. 4.0 Unsupported Configurations ========================= Configurations that are not supported with this level of code are listed below. Fibre Channel loop environments with the IBM Netfinity Fibre Channel Hub, machine type 3523, in conjunction with the IBM Fibre Channel Switch, types 2109-S16 or 2109-S8. In this configuration, the hub is connected between the switch and the Fibre Channel RAID Controllers. 5.0 WEB Sites and Support Phone Number ================================== 5.1 IBM Support Web Site: http://www.ibm.com/pc/support 5.2 IBM eServer xSeries Marketing Web Site: http://www.ibm.com/pc/us/eserver/xseries/index.html 5.3 If you have any questions about this update, or problem applying the update go to the following Help Center World Telephone Numbers URL: http://www.ibm.com/planetwide 6.0 Trademarks and Notices ======================= 6.1 The following terms are trademarks of the IBM Corporation in the United States or other countries or both: IBM Other company, product, and service names may be trademarks or service marks of others. 7.0 Disclaimer ============ 7.1 THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 7.2 Note to U.S. Government Users -- Documentation related to restricted rights -- Use, duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation.