IBM Advanced Systems Management Adapter Configuration and Device Driver Diskette Version 2.0 This README file contains information pertaining to the Advanced Systems Management Adapter. CONTENTS ________ 1.0 Other Required Software 2.0 Known Limitations 3.0 Note to Novell Netware users 4.0 Trademarks and Notices 1.0 Other Required Software ____________________________ This section lists other software that must be installed in order to utilize the full functionality of this software update. o Service Processor Manager version 2.0 or higher for Netfinity Manager or Client Services version 5.0 or above. o Your system must have the minimum level POST/BIOS listed below installed: System Type Models Level ______ ____ ______ _____ PC Server 325 8639 -EJ0, -ES0, -RS0, -ESV 40A or higher PC Server 325 8639 -PT0, -PTW, -PB0, -RB0 12A or higher PC Server 330 8640 -EM2, -ES0, -ES2, -ESS 40A or higher PC Server 330 8640 -PT0, -PTW, -PB0 12A or higher BIOS updates are available by calling the IBM HelpCenter or for downloading over the World Wid Web. Enter the following URL: http://www.pc.ibm.com 2.0 Known Limitations ______________________ The following limitations exist with the current adapter firmware, system hardware, or system firmware. - Dialout on "Tamper Alerts" for physical tamper is not supported. Dialout on "Tamper Alerts" for remote tampers is supported. A remote tamper is defined as six consecutive failed login attempts. - Use of the Caller ID string is not supported - Alerts for redundant power supply failures is not supported - Alerts for "Boot failures" are not supported 3.0 Note to Novell NetWare users _________________________________ During the installation process a line is added to the AUTOEXEC.NCF file which automatically loads the Advanced Systems Management Adapter device driver (IBMSPN.NLM) whenever NetWare is started. There are three additional parameters on this line that tell the driver how to communicate with the Advanced Systems Management Adapter card. If the driver is ever unloaded and reloaded manually from the NetWare console screen, be sure to use the same parameters that are shown in the AUTOEXEC.NCF file. If different parameters are used, the system may hang or abnormally end (ABEND). --- HOW TO FIX AN AUTOEXEC.NCF THAT CONTAINS INCORRECT PARAMETERS --- If the line in the AUTOEXEC.NFC file that loads the Advanced Systems Management Adapter device driver (IBMSPN.NLM) is accidentally changed, and the additional parameters are not correct, it is recommended that the device driver be installed again, using the Advanced Systems Management Adapter device driver installation process. If this cannot be done because the system hangs or ABENDs when NetWare is booted, then the line needs to be commented out or removed from the AUTOEXEC.NCF file by using the following commands: boot the system in DOS cd nwserver server -na This starts NetWare without executing the AUTOEXEC.NCF file, and the AUTOEXEC.NCF file can now be edited to comment out or remove the line that loads the IBMSPN.NLM driver. NetWare can now be restarted normally and the device driver can be installed again, using the Advanced Systems Management Adapter device driver installation process. 4.0 Trademarks and Notices ___________________________ The following terms are trademarks of the IBM Corporation in the United States or other countries or both: IBM Netfinity The following terms are trademarks of the Novell Corporation in the United States or other countries or both: Novell NetWare THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. Note to U.S. Government Users -- Documentation related to restricted rights -- Use, duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corp.